This is all done on a cold engine with the manifold and flapper motor in place. The flapper motor cannot travel out of range with this bracket in place despite how much wear might be on your linkage arm. Country of Manufacture: Not Specified Manufacture Quality: Genuine Shipping Weight lbs : 0. Installation is basically the reverse: 7 Get the motor in position and press the linkage onto the ball. With wire, create a secure loop I used a cable ferrule to secure the metal part of the flap-motor arm just inboard of the forward spring hook notch. I may have to do just that at some point, if the E-clip fix doesn't hold up long term.
It will not require removing anything to install. Implementation of this fix has proved to be a quick and easy solution to many if not most P2015 codes. We will not provide a replacement or credit for any part not purchased directly from our store. Then go to zero deg. I used a common flat washer to use as a guide for cutting the groove. The Intake Manifold Flap Motor V157 and Manifold Runner Position Sensor G336 may be Part of the same Unit. We also provide inexpensive and guaranteed 3 day, 2 day, and Overnight shipping options, so if you need your Intake Manifold Position Sensor Potentiometer tomorrow, eEuroparts.
However, being a single guy with a single car, I don't like to tackle the big projects these days unless I'm absolutely sure of what I'm digging into. I hope you will have it available soon, I will order a timing belt kit from you within a couple of months and wouid like to order it together. We use data about you for a number of purposes explained in the links below. By continuing to browse our site you agree to our use of data and cookies. Will post pics and more details on Friday. Since joining the Volkswagen Group in 1966 Audi has propelled the automotive industry through innovation and progressive design and engineering.
Does it just pull right out? It seems the new linkage is a 'best guess', but is not trialed as far as I can tell. This site was designed and produced solely by Pelican Parts. I was surprised, since there is a return line on each injector. Over time, a limiting stop on the travel of the motor and butterfly valve assembly wears down, to the point that the valve assembly will no longer actuate. Maybe someone can think of a simple way to limit the movement of that motor Arm.
If the snap ring does not work I might try drilling a small hole and installing safety wire to keep linkage from sliding off again. The Intake Manifold Flap Motor V157 and Manifold Runner Position Sensor G336 may be Part of the same Unit. The item must be new and in its original manufacturer packaging to be eligible for a cash refund. I really think he is onto something. The linkage that connects the motor to the flap assembly binds up. Pulled the motor off and tried your trick of installing a snap ring.
I need to first test it to make sure that's really what's throwing the code, but I'm sure it will be just like yours. If a part fails, the original purchaser is able to return that part at any time for replacement. If it doesn't hold up long-term, then I get the intake manifold replaced. Do I have your authorization to proceed? If you would like to return an item or have questions about the process, please and one of our customer service experts will be happy to help. Easier to install, and maybe I could have made a smaller groove than using a hacksaw blade.
Only the original purchaser of the part can receive a credit after they have purchased a replacement. Unfortunately it seems this must be done with the engine running. By entering this site, you agree to hold Pelican Parts free from any liability arising out of the use of any information contained within. If your flap is jammed, when the car is idling and the joint is in the rearward in-car position, prodding the linkage with a screwdriver wedged against the intake manifold casting should get the linkage to 'pop', it'll be freed, and will pivot forward. Run the zip-tie through the engine hoist loop and tighten it only enough to take up the slack in the wire. I'll post a pic or two and promise to update when I'm sure it is really fixed. You will only need to affix the bracket to the motor and bolt it together.
Information and technical articles within this website are for reference only. If there is anything you cannot find in our catalog please and our knowledgeable customer service team will help you locate the part you need, fast. So last night my brother and I were trying to figure this out. Has anyone found a solution to the intake manifold flapper motor issue? I have a fix clip for this problem that I'm in the finishing prototype phase of development. This was my case, the same as Ray Martinez'.